PL-65 High Speed Hydraulic Power-Lift Jack Plate

#22 CMC Position Indicator Gauge Kit P/N 6077

his kit is used to add a gauge to your outboard Jack plate from CMC Marine. Simple installation using your small hands and lots of patience. Buy this Gauge Kit for CMC Jack Plate 6077 to have a safe and convenient height determination of your boat. Use...

#07 CMC High Speed Hydraulic Actuator 7342 - PL-65

The CMC high speed hydraulic actuator is a direct replacement for the actuator installed in your high speed jack plate. It can also replace the 7050 actuator in CMC jackplates (cannot be used in the PT-130) P/N 7342 CMC hydraulic actuator is new and not...

CMC Position Indicator Gauge 6045

CMC Position Indicator Gauge 6045 CMC Jack Plate Position Indicator Gauge #6045 Features: This CMC Position Indicator Gauge 6045 is used to determine the height of the motor without looking back, allowing the driver to maintain a forward view at...

Diesel tachometer sending unit 8 pulse per revolution replaces Faria P/N 90901

Replacement for Faria Diesel Tachometer Sender Part Number 90901 Faria Discontinued this tachometer sending unit, but we found a replacement for it. It is a direct fit and wires right up to your existing 8 pulse per revolution tachometer.   Diesel...

#12 CMC PL-65 Bronze Bearing (Set of 4)

These bronze bearings are the part that slides in the grooves in the motor rails. Qty of 4 required to assemble a jackplate. Two for the starboard side and two for the port side.

#13 CMC PL-65 Nylatron Flat Washer (Set of 8)

These nylatron flat washers are the part that slides outside the grooves on the motor rails. Qty of 8 required to assemble a jackplate. Four for the starboard side and for for the port side.

#14 CMC PL-65 Aluminum Flat Washer (Set of 4)

These aluminum flat washers are the part that prevents the bolt from cutting into the nylatron flat washers.1/4" X 3/4" X 2" aluminum flat washer Qty of 4 required to assemble a jackplate. Two for the starboard side and two for the port side.

#16 CMC PL-65 External Tooth Lock Washer (Set of 8)

These external tooth lock washers are the part holds the top bracket to the motor rails and the bottom bracket to the transom rails.1/2"" external tooth lock washer is made from 410 Stainless Steel Qty of 8 required to assemble a jackplate. Four for the...

#15 CMC PL-65 Hex Head Cap Screw (Set of 8)

These hex head cap screws are the part holds the top bracket to the motor rails and the bottom bracket to the transom rails.1/2 - 13 X1" hex head cap screw Qty of 8 required to assemble a jackplate. Four for the top bracket and four for the bottom...

CMC Wiring Harness Circuit Breaker

 CMC Circuit Breaker #7186 Features: This CMC Circuit Breaker 7186 is used to eliminate any simple problems that might arise. This CMC 7186 is available for jack plates & tilt trim.

#25 CMC Toggle Switch Rubber Boot

This Tilt and Trim Toggle Switch Rubber Boot, CMC-7124, is ready to ship to help repair your tilt trim unit.

#26 CMC Toggle Switch Plate

This Tilt and Trim Toggle Switch Plate, CMC-51380, is ready to ship to help repair your tilt trim unit.

#04 CMC PL-65 Starboard Side Transom Rail

This starboard side transom rail, CMC-6004, is ready to ship to help repair your jack plate.

CMC Position Indicator Gauge Sending Unit 6214

CMC Sending Unit Gauge #6214: This CMC Sending Unit Gauge 6214 is only used for CMC jack plate. Get this CMC Sending Unit Gauge 6214 for your convenience.

#8 CMC PL-65 bottom Spring Pin

This bottom spring pin is made of 304 stainless steel and is 1/2" X 1 1/2"