CMC

#09 CMC PT-130 Hex Head Cap Screw (Set of 8)

These hex head cap screws are the part holds the top bracket to the motor rails and the bottom bracket to the transom rails.1/2 - 13 X1" hex head cap screw Qty of 8 required to assemble a jackplate...

#10 CMC PT-130 External Tooth Lock Washer (Set of 8)

These external tooth lock washers are the part holds the top bracket to the motor rails and the bottom bracket to the transom rails.1/2"" external tooth lock washer is made from 410 Stainless...

#12 CMC PL-65 Bronze Bearing (Set of 4)

These bronze bearings are the part that slides in the grooves in the motor rails. Qty of 4 required to assemble a jackplate. Two for the starboard side and two for the port side.

#13 CMC PL-65 Nylatron Flat Washer (Set of 8)

These nylatron flat washers are the part that slides outside the grooves on the motor rails. Qty of 8 required to assemble a jackplate. Four for the starboard side and for for the port side.

#14 CMC PL-65 Aluminum Flat Washer (Set of 4)

These aluminum flat washers are the part that prevents the bolt from cutting into the nylatron flat washers.1/4" X 3/4" X 2" aluminum flat washer Qty of 4 required to assemble a jackplate. Two for...

#14 CMC PT-130 Nylatron Flat Washer (Set of 4)

These nylatron flat washers are the part that slides between the motor rail and the transom rail. Qty of 4 required to assemble a tilt trim unit. Twp for the starboard side and two for the port side.

#14 CMC PT-35 Spring Pin

This spring pin is made of 304 stainless steel and is 1/2" X 3 1/2" Two required to assemble a PT-35 power tilt and trim unit

#15 CMC PL-65 Hex Head Cap Screw (Set of 8)

These hex head cap screws are the part holds the top bracket to the motor rails and the bottom bracket to the transom rails.1/2 - 13 X1" hex head cap screw Qty of 8 required to assemble a jackplate...

#16 CMC PL-65 External Tooth Lock Washer (Set of 8)

These external tooth lock washers are the part holds the top bracket to the motor rails and the bottom bracket to the transom rails.1/2"" external tooth lock washer is made from 410 Stainless...

#17 CMC PT-130 Spring Pin

This spring pin is made of 304 stainless steel and is 1/2" X 3 1/2" Two required to assemble a PT-130 tilt trim unit

#19 CMC Jack Plate Wiring Harness 7014G

CMC Jack Plate and Tilt Trim Wiring Harness 7014G Features: This CMC Wiring Harness is designed for all Cook Manufacturing Company's hydraulic jack plates with or without gauge (PL-65, Pl-65-10,...

#20 CMC Up-down Toggle Switch 7123

 CMC Jack Plate Up-down Toggle Switch #7123 This CMC Up-Down Toggle Switch 7123 will make the Power-Lift operational.  Try the CMC Toggle Switch 7123 up to make sure it runs up; and down...

#21 CMC Toggle Switch Rubber Boot

This Tilt and Trim Toggle Switch Rubber Boot, CMC-7124, is ready to ship to help repair your tilt trim unit.

#22 CMC Position Indicator Gauge Kit P/N 6077

his kit is used to add a gauge to your outboard Jack plate from CMC Marine. Simple installation using your small hands and lots of patience. Buy this Gauge Kit for CMC Jack Plate 6077 to have a safe...

#22 CMC PT-130 Spacer For Bottom of Hydraulic Actuator

This CMC spacer, CMC-51392, is ready to ship to help repair your tilt trim unit. These CMC PT-130 spacers go over the bottom of the hydraulic actuator.