#07 CMC Hydraulic Actuator 7050 - PT-130

The CMC high speed hydraulic actuator is a direct replacement for the actuator installed in your high speed jack plate. It can also replace the 7342 actuator in CMC jackplates (cannot be used in the PT-130) P/N 7050 CMC hydraulic actuator is new and not...

CMC Position Indicator Gauge 6045

CMC Position Indicator Gauge 6045 CMC Jack Plate Position Indicator Gauge #6045 Features: This CMC Position Indicator Gauge 6045 is used to determine the height of the motor without looking back, allowing the driver to maintain a forward view at...

#22 CMC PT-130 Spacer For Bottom of Hydraulic Actuator

This CMC spacer, CMC-51392, is ready to ship to help repair your tilt trim unit. These CMC PT-130 spacers go over the bottom of the hydraulic actuator.

Diesel tachometer sending unit 8 pulse per revolution replaces Faria P/N 90901

Replacement for Faria Diesel Tachometer Sender Part Number 90901 Faria Discontinued this tachometer sending unit, but we found a replacement for it. It is a direct fit and wires right up to your existing 8 pulse per revolution tachometer.   Diesel...

#14 CMC PT-130 Nylatron Flat Washer (Set of 4)

These nylatron flat washers are the part that slides between the motor rail and the transom rail. Qty of 4 required to assemble a tilt trim unit. Twp for the starboard side and two for the port side.

#10 CMC PT-130 External Tooth Lock Washer (Set of 8)

These external tooth lock washers are the part holds the top bracket to the motor rails and the bottom bracket to the transom rails.1/2"" external tooth lock washer is made from 410 Stainless Steel Qty of 8 required to assemble a jackplate. Four for the...

#09 CMC PT-130 Hex Head Cap Screw (Set of 8)

These hex head cap screws are the part holds the top bracket to the motor rails and the bottom bracket to the transom rails.1/2 - 13 X1" hex head cap screw Qty of 8 required to assemble a jackplate. Four for the top bracket and four for the bottom...

CMC Wiring Harness Circuit Breaker

 CMC Circuit Breaker #7186 Features: This CMC Circuit Breaker 7186 is used to eliminate any simple problems that might arise. This CMC 7186 is available for jack plates & tilt trim.

#26 CMC Toggle Switch Rubber Boot

This Tilt and Trim Toggle Switch Rubber Boot, CMC-7124, is ready to ship to help repair your tilt trim unit.

#27 CMC Toggle Switch Plate

This Tilt and Trim Toggle Switch Plate, CMC-51380, is ready to ship to help repair your tilt trim unit.

#06 CMC PT-130 Bottom Clevis Bracket

This bottom clevis bracket, CMC-51300, is the piece that holds the port side transom rail to the starboard side transom rail and connects to the hydraulic actuator.

#05 CMC PT-130 Top Clevis Bracket

This top clevis bracket, CMC-51290, is the piece that holds the port side motor rail to the starboard side motor rail and connects to the hydraulic actuator.

CMC Position Indicator Gauge Sending Unit 6214

CMC Sending Unit Gauge #6214: This CMC Sending Unit Gauge 6214 is only used for CMC jack plate. Get this CMC Sending Unit Gauge 6214 for your convenience.

#17 CMC PT-130 Spring Pin

This spring pin is made of 304 stainless steel and is 1/2" X 3 1/2" Two required to assemble a PT-130 tilt trim unit

#25 CMC Up-down Toggle Switch 7123

 CMC Jack Plate Up-down Toggle Switch #7123 This CMC Up-Down Toggle Switch 7123 will make the Power-Lift operational.  Try the CMC Toggle Switch 7123 up to make sure it runs up; and down to make sure it runs down. Get this CMC Up-Down Toggle...