Boat Parts

#22 CMC Position Indicator Gauge Kit P/N 6077

his kit is used to add a gauge to your outboard Jack plate from CMC Marine. Simple installation using your small hands and lots of patience. Buy this Gauge Kit for CMC Jack Plate 6077 to have a safe and convenient height determination of your boat. Use...

#07 CMC High Speed Hydraulic Actuator 7342 - PL-65

The CMC high speed hydraulic actuator is a direct replacement for the actuator installed in your high speed jack plate. It can also replace the 7050 actuator in CMC jackplates (cannot be used in the PT-130) P/N 7342 CMC hydraulic actuator is new and not...

#07 CMC High Speed Hydraulic Actuator 7342 - PT-35

The CMC high speed hydraulic actuator is a direct replacement for the actuator installed in your high speed jack plate. It can also replace the 7050 actuator in CMC jackplates (cannot be used in the PT-130) P/N 7342 CMC hydraulic actuator is new and not...

#07 CMC Hydraulic Actuator 7050 - PT-130

The CMC high speed hydraulic actuator is a direct replacement for the actuator installed in your high speed jack plate. It can also replace the 7342 actuator in CMC jackplates (cannot be used in the PT-130) P/N 7050 CMC hydraulic actuator is new and not...

#19 CMC Jack Plate Wiring Harness 7014G

CMC Jack Plate and Tilt Trim Wiring Harness 7014G Features: This CMC Wiring Harness is designed for all Cook Manufacturing Company's hydraulic jack plates with or without gauge (PL-65, Pl-65-10, PL-65SS) and Tilt Trim Units (PT -130 and PT-35). CMC Jack...

CMC Position Indicator Gauge 6045

CMC Position Indicator Gauge 6045 CMC Jack Plate Position Indicator Gauge #6045 Features: This CMC Position Indicator Gauge 6045 is used to determine the height of the motor without looking back, allowing the driver to maintain a forward view at...

#22 CMC PT-130 Spacer For Bottom of Hydraulic Actuator

This CMC spacer, CMC-51392, is ready to ship to help repair your tilt trim unit. These CMC PT-130 spacers go over the bottom of the hydraulic actuator.

Diesel tachometer sending unit 8 pulse per revolution replaces Faria P/N 90901

Replacement for Faria Diesel Tachometer Sender Part Number 90901 Faria Discontinued this tachometer sending unit, but we found a replacement for it. It is a direct fit and wires right up to your existing 8 pulse per revolution tachometer.   Diesel...

#12 CMC PL-65 Bronze Bearing (Set of 4)

These bronze bearings are the part that slides in the grooves in the motor rails. Qty of 4 required to assemble a jackplate. Two for the starboard side and two for the port side.

#14 CMC PT-130 Nylatron Flat Washer (Set of 4)

These nylatron flat washers are the part that slides between the motor rail and the transom rail. Qty of 4 required to assemble a tilt trim unit. Twp for the starboard side and two for the port side.

#13 CMC PL-65 Nylatron Flat Washer (Set of 8)

These nylatron flat washers are the part that slides outside the grooves on the motor rails. Qty of 8 required to assemble a jackplate. Four for the starboard side and for for the port side.

#14 CMC PL-65 Aluminum Flat Washer (Set of 4)

These aluminum flat washers are the part that prevents the bolt from cutting into the nylatron flat washers.1/4" X 3/4" X 2" aluminum flat washer Qty of 4 required to assemble a jackplate. Two for the starboard side and two for the port side.

#10 CMC PT-130 External Tooth Lock Washer (Set of 8)

These external tooth lock washers are the part holds the top bracket to the motor rails and the bottom bracket to the transom rails.1/2"" external tooth lock washer is made from 410 Stainless Steel Qty of 8 required to assemble a jackplate. Four for the...

#16 CMC PL-65 External Tooth Lock Washer (Set of 8)

These external tooth lock washers are the part holds the top bracket to the motor rails and the bottom bracket to the transom rails.1/2"" external tooth lock washer is made from 410 Stainless Steel Qty of 8 required to assemble a jackplate. Four for the...

#09 CMC PT-130 Hex Head Cap Screw (Set of 8)

These hex head cap screws are the part holds the top bracket to the motor rails and the bottom bracket to the transom rails.1/2 - 13 X1" hex head cap screw Qty of 8 required to assemble a jackplate. Four for the top bracket and four for the bottom...